A discontinued component does not always force a new PCB. Stock the company already holds, a manufacturer's designated channel for obsolete products, licensed aftermarket production or a carefully qualified replacement can keep the released design in service for years. Each of those routes carries different evidence, cost and availability, and none of them removes the need for qualification.
This guide is for the case where the part has already gone obsolete and the product must stay as it is. If the discontinuance notice is still open and a final order is possible, read planning a last-time buy first; it is usually cheaper to buy during the notice period than after it.
Confirm the part really is obsolete
Start with the exact orderable part number, including the package and grade suffix, and get the manufacturer's own notice. Lifecycle words differ between manufacturers. NXP, for instance, separates "End of Life", when orders can still be placed until the last-time-buy date, from "No Longer Manufactured", when it no longer accepts orders. One package variant may be withdrawn while another stays active, so check every suffix.
Then search internal records for approved alternates, earlier last-time-buy decisions and change notices. Establish what the shortage actually affects: new production, warranty repair, field service or a test fixture. The quantity, quality level and consequence of failure decide which options below are acceptable.
IEC 62402:2019, the international standard for obsolescence management, treats this as a managed process with a policy, a plan and selected resolutions, not as a one-off purchase. In practice, open a case with an owner, the affected BOM revisions, a required-by date and an approval route.
Decide what "without redesign" allows
Set the boundary before anyone starts searching. "No redesign" can mean any of these, and they are not the same:
- no PCB layout change;
- no enclosure or connector change;
- no firmware change;
- no new regulatory submission;
- no change to the form, fit or function the customer approved;
- no change to field-service instructions.
A pin-compatible replacement may keep the PCB but need a firmware tweak and a validation run. A licensed aftermarket part in the original package may still need incoming checks and application testing. Write down which changes are permitted and who approves them. If the only workable option breaks the boundary, escalate the redesign decision openly rather than passing the change off as a simple substitution.
Work through the sources in order
Begin with the routes that keep provenance and manufacturer support clearest, and move down only when the route above is exhausted.
Internal and partner stock
Search every approved location: company stores, the EMS, repair depots and consignment stock. Reconcile part number, ownership, lot, date code, quantity, packaging condition, storage history and existing allocations. Stock can move from a cancelled or declining programme once engineering confirms it is the same item at the same quality level, quality has reviewed traceability and storage records, and finance has approved the transfer of value.
Unlabelled engineering samples, returned assemblies and loose parts from a laboratory drawer are not production inventory.
The manufacturer and its authorised distributors
Ask the original component manufacturer and its authorised distributors for residual finished stock, cancelled allocations and inventory in other regions. Confirm the seller is authorised for that brand and product line.
Some manufacturers name a specific channel for obsolete parts. TI's ordering FAQ lists Rochester Electronics as a channel for obsolete or surplus TI semiconductors, notes that different TI warranty terms may apply there, and states that TI does not provide warranty coverage or support for parts bought outside its authorised network (checked October 2026). That is TI's policy only; check each manufacturer's current page for its own.
Ask for written confirmation of manufacturer, part number, source, lot, date code, warranty, traceability and whether the stock was built by the original manufacturer or by an aftermarket manufacturer.
Authorised aftermarket suppliers
An authorised aftermarket supplier may hold the original manufacturer's finished goods, banked die or wafers, or the rights and process information to keep building selected parts. That is different from a broker reselling stock of unknown origin.
Rochester Electronics says it works in partnership with more than 70 component manufacturers and holds a large die bank alongside its manufacturing capability. Its NXP page describes authorised, traceable inventory of active and end-of-life NXP devices, and continued production of some discontinued devices through licensed manufacturing with NXP's support. Lansdale Semiconductor says it makes classic IC designs in their original packages, as first produced by companies including Motorola, Intel and National. (Both checked October 2026.)
None of this means a particular part is available or interchangeable. For the quoted item, verify the part number, the authorisation or licence, the datasheet revision, the fabrication and assembly information available, quality grade, marking, qualification evidence and warranty.
A form-fit-function replacement
A replacement keeps the board if package and pinout match and the behaviour is close enough. Look past headline function and compare absolute and recommended limits, DC and AC characteristics, timing, start-up and reset, analogue offset and noise, package and thermal data, moisture sensitivity, firmware-visible device IDs and registers, errata, qualification grade and compliance documents. Classify the outcome as drop-in, firmware change only, validation only or redesign required. The full comparison method is in qualifying cross-reference and alternate parts.
Die, package conversion or emulation
For high-value legacy equipment, a specialist may package known die, convert a supported package or offer a hardware emulation. This can make sense when volumes are small and requalifying a redesign would be very expensive. Ask who owns the design and die, whether manufacture is licensed, what process and package changes exist, how the new date code is marked and what qualification supports the claimed function. An emulation is not the original component, and should not be recorded as one.
A qualified independent distributor
Leave authorised channels only through a documented exception. SAE AS6081A sets practices for independent distributors on identifying reliable sources, reducing counterfeit risk, controlling suspect parts and reporting them. Qualify both the supplier and the quoted lot: chain of custody, upstream source, photographs of the actual stock, packaging, lot and date codes, storage history, return terms and permission for independent inspection. Confirm the seller physically holds the lot. The purchase order should forbid unapproved substitution and set out quarantine, testing, rejection and disposal of counterfeit material. Authorised versus independent distributors compares the two channels in more depth.
Reclaimed parts, as a last resort
Parts taken out of used equipment can carry unknown operating stress, rework cycles and moisture exposure. Reclamation is sometimes considered for low-volume repair of non-critical legacy equipment when no new source exists and the organisation has a written engineering and quality process for removal, cleaning, lead or ball restoration, inspection, electrical test and traceability. Never mix harvested parts into new-production stock or describe them as new. Safety-critical, regulated and customer-controlled products may prohibit them outright.
Apply one validation gate to every option
Every candidate lot or replacement passes four reviews before use.
Technical. Engineering confirms part number, revision, package, ratings, behaviour, software impact and margin in the application, using bench comparison, environmental tests, timing analysis and regression tests as needed.
Source and authenticity. Quality classifies the source (manufacturer, authorised distributor, authorised aftermarket, independent or reclaimed), and the evidence demanded rises as certainty falls. SAE AS6171A sets general requirements for inspecting and testing suspect counterfeit parts where the chain of custody is unknown, and states that no amount of testing can confirm an item as authentic. Tests such as external visual inspection, X-ray, XRF, electrical testing and decapsulation each target particular risks; a qualified engineer should choose them, and a laboratory listed under testing and certification services can carry them out. Counterfeit IC checks explains the sequence.
Manufacturing. The EMS or repair site confirms packaging, moisture sensitivity, solderability, programming, placement and reflow, then runs a trial build and watches first-pass yield.
Commercial. Product management and finance compare available quantity with remaining demand and warranty obligations, adding unit price, inspection cost, yield loss and leftover stock. They also check whether continuing the old design is still cheaper than redesigning over the product's remaining life.
Write a lot-level acceptance plan
Approving a supplier's name does not approve its next lot. The purchase and inspection plan should state the exact part number and permitted date-code range, manufacturer and stated origin, source class and upstream evidence, packaging and storage condition, sample size and test sequence, acceptance and rejection criteria, the number of parts that will be destroyed in testing, how traceability carries into finished serial or lot numbers, and what happens to failed material.
Hold stock in quarantine until the evidence and results are approved. Keep reference samples where that is justified. If two lots differ in marking, package construction or electrical spread, investigate the difference instead of averaging the results.
Questions people ask
Is an authorised aftermarket part the same as the original?
It may be built from original finished stock, original die or licensed design data, but programmes differ. Check the part number, the relationship with the original manufacturer, process, package, qualification, marking and warranty for the specific item quoted.
Can testing make broker stock safe?
Testing reduces specific risks. It cannot recreate a missing chain of custody or prove every latent reliability attribute, so use qualified suppliers, tests matched to the risk and a named person who accepts the residual risk.
When does a redesign become unavoidable?
When safe, conforming supply cannot be shown; when remaining demand is larger than any credible stock; when continuation costs more than a redesign over the remaining life; or when customer, regulatory or reliability requirements can no longer be met. Keep that trigger written into the case so the decision is reviewed, not drifted into.
Sources
Each source was opened and checked on the date shown. Rules, rates and company details change, so confirm anything time-sensitive before you act on it.
- IEC 62402:2019 Obsolescence management
- Ordering FAQs: authorized distributors
- Manufacturers
- NXP microcontrollers and microprocessors
- Lansdale Semiconductor home page
- AS6081A: Counterfeit EEE Parts: Avoidance, Detection, Mitigation, and Disposition - Independent Distribution
- AS6171A: Test Methods Standard; General Requirements, Suspect/Counterfeit, Electrical, Electronic, and Electromechanical Parts
- Product lifecycle
Continue on forUdyog
Have a specific requirement? Describe it on the QUICK RFQ page.
